Increase the separation between equipment and receiver. If it still does not fit, contact a qualified electrician. Do not operate this appliance near flammable liquids or in gaseous or explosive atmospheres. Have plenty of fresh water and soap nearby in case battery acid contacts skin. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected. Please be advised that the battery is designed to last the service life of the uni and is not replaceable, removable or serviceable. When charging is complete, disconnect the AC charging adapter first unplug the adapter from the AC power source, then disconnect the barrel connector from the unit. Always store battery clamps when not in use. It might spark or short-circuit the battery or another electrical part, and that may cause an explosion. The EverStart PPS1CWE Maxx 1000 Amp Battery Jump-Starter with Wireless Charging is a powerful and versatile tool that can be used to jump-start vehicles, charge mobile devices, and even inflate tires. A beep will sound and the backlit LCD screen will display the Battery Status Icon, Battery Voltage Indicator, the Clamp Icons, and the + and signs, as well as the flashing Jump Starter Icon. Attach clamps to battery and chassis as indicated in "Battery Installed in Vehicle" steps 5 and 6, or in "Battery Outside of Vehicle" steps 2 to 5. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. For a battery without cell caps (maintenance free), carefully follow manufacturer's charging instructions. When desired pre-set pressure is reached, the compressor will automatically stop. Ensure that unit is completely disconnected from battery and power source before cleaning. Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at (877) 571-2391. DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Use the unit for charging/boosting a lead-acid battery only. Before proceeding, check the units battery status on the LCD screen. How to Charge Everstart Maxx Flashlight | 8 Simple Steps Set up the battery charger and connect to the battery following steps 1 through 2 in the "Charging the Battery" section. Make sure that the total draw of all USB devices plugged into the two USB Ports does not exceed 3.1A. Here's how: 1. The Compressor Icon will flash and the digital display will only show the current pressure value which will light solid) to indicate the compressor is activated. Recommended accessories for use with your tool may be available from the manufacturer. The empty Battery Status Icon will flash for a short period of time before automatic shut down. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. Danger Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Press the Alternator Check Button to start the check. Stand as far back from the battery as possible, and do not face battery when making final connection. Always disconnect the negative (black) jumper cable first, followed by the positive (red) jumper cable, except for positive grounded systems. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or property damage. Keep children away. RISK OF UNSAFE OPERATION. If the clamp connections to the batterys positive and negative terminals are reversed. Connect to a heavy gauge metal part of the frame or engine block. Make sure the unit is not being operated in the compressor mode. Comment * document.getElementById("comment").setAttribute("id","aeb266a2cfc60001d263e163aa691acc");document.getElementById("afe6277d1c").setAttribute("id","comment"); Save my name, email, and website in this browser for the next time I comment. These batteries may burst and cause injury to persons and damage property. Periodic reconditioning is recommended to maintain a battery's optimum performance. The EverStart MAXX PPS1CWE 1000 Amp Jump Starter icon will flash to indicate the clamps are properly connected. A beep will sound, the USB Power/Fault Indicators around each of the USB Ports will light blue and the LCD screen will continuously display the following The Battery Status Icon and Battery Voltage Indicator will light solid, as well as the USB Icon, indicating the USB ports are ready to use.2. Before jump-starting, read the vehicle's owner's manual to confirm that external-starting assistance is suitable. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Use of accessories and attachments. Always turn the unit off when not in use. Never submerge this unit in water; do not expose it to rain, snow or use when wet. Do not operate this equipment when you are tired or impaired. Never allow red and black clamps to touch each other or another common metal conductor. This equipment employs parts (switches, relays, etc.) Never smoke or allow a spark or flame in vicinity of vehicle battery, engine or power station. Sure Fit is a registered trademark owned by Baccus Global, LLC. Operation is subject to the following two conditions this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. APPENDIX The two USB Ports provide a total of 3.1A (5V each). The Everstart Maxx BC50BE 15 Amp Automotive Battery Charger is a versatile and reliable tool for charging and maintaining your vehicle's battery. If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or repaired in the following ways: (1) Return the product to the manufacturer for repair or replacement at manufacturer's option. Receptacles are available having built in GFCI protection and may be used for this measure of safety. FOR THIS REASON, IT IS OF THE UTMOST IMPORTANCE THAT EACH TIME BEFORE USING THE BATTERY CHARGER YOU READ THIS MANUAL AND FOLLOW INSTRUCTIONS EXACTLY. Periodically inspect the condition of adapters, connectors and wires. It is important to note that overcharging the battery can reduce its lifespan and performance. Never attempt to jump-start or charge a frozen battery. charging the jump starter. The Alarm Icon, the + and signs and the Reverse Polarity Icons will flash and the unit will sound a warning continuously until the clamps are disconnected from the battery. WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS DANGEROUS. Add distilled water in each cell until battery acid reaches level specified by battery manufacturer. The Battery Status Icon and Battery Voltage Indicator light solid. Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire. It is not qualified for marine applications. Do not wrap them around the unit or crimp them with a tight band. To reduce the risk of battery explosion, follow these instructions and those published by the battery manufacturer and manufacturer of any equipment you intend to use in the vicinity of the battery. CAUTION Risk of property damage: Failure to keep the battery charged will cause permanent damage and result in poor jump starting performance. Recharging the battery after each use will prolong battery life; frequent heavy discharges between recharges and/or overcharging will reduce battery life.3. Manufacturer suggests leaving the unit charging for a period of 20 hours using the supplied AC charger before use. The display will read FL. How to Charge Your EverStart Maxx Jump Starter - Step-by-Step Guide Allow the unit to cool for 10-30 minutes before use. If low battery voltage fault occurs, the USB Power/Fault Indicators will turn off. When an extension cord is used, make sure that the pins of extension cord are th e same number, size and shape as those in the charger the extension cord is properly wired and in good electrical condition, the wire size is large enough for the AC rating of the charger. If a fault condition exists in either of the USB Ports, the USB Power/Fault Indicators will flash blue. Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. The Compressor Power Button and Increase + and Decrease Compressor Pressure Control Buttons are located on the control panel on the front of the unit. Turn on the jump starter box by pressing its "power" button. Turn the EverStart Maxx switch to the ON position. POSITIVE (POS, P, +) battery post usually has larger diameter than NEGATIVE (NEG, N, ) post. Operate battery charger only as described in this Instruction Manual. 5. When the compressor is operated at higher PSIs, the unit may operate normally for several minutes, then rev down for a few minutes before returning to normal operation. Some appliances may not charge/operate with this unit. MAKE SURE THAT THE ALTERNATOR IS RATED TO SUPPORT THE APPLICATION. To recharge this unit, use only the supplied AC charger. The backlit LCD screen will display the following The Battery Status Icon, the Battery Voltage Indicator, Clamp Icons and the + and signs light solid to indicate the unit is jump-starting. Check that the unit has a full charge. Determine voltage of battery to be charged by referring to the vehicle manual. The backlit LCD screen will display the flashing Wireless Charging Indicator. The LCD screen will display the following*: When "00" is reached, a beep will sound, engine start icon (. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. Reorient or relocate the receiving antenna. If the red and black clamps touch each other, the unit will sound a continuous two-second alarm every ten seconds until the clamps are separated. Everstart Maxx Battery Charger User Guide: BC50BE 15 Amp - Manuals+ Never touch battery clamps together. WARNING Do not dispose of the battery in fire as this may result in an explosion. If battery acid contacts skin or clothing, wash immediately with soap and water for at least 10 minutes and get medical attention immediately. Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This is the Everstart Maxx power station review. How do you want your items? Locate charger as far away from battery as cables permit. If the engine does not start within 3 seconds, stop cranking and wait at least 1 minute before attempting to start the vehicle again. If liquid crystal is swallowed: Flush your mouth thoroughly with water. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 18 of the FCC Rules. If the unit detects that the alternator is out of typical voltage range, the backlit LCD screen will display the following The Battery Status Icon, Alternator Icon and ALT will light solid. They only provide power to external USB powered devices. Battery recondition sends a series of electrical pulses to break up the crystalline form of lead sulfate and turn these chemicals into useful battery electrolytes. The use of any accessory or attachment not recommended for use with this appliance could be hazardous. The unit remains on until the USB Power Button is pressed again to turn it off. Place the appliance in the center of the Wireless Charging Pad. SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. If the compressor must be operated for longer periods every 10 minutes press the Compressor Power Button to turn the compressor off, then restart after a cooling down period of approximately 30 minutes. 6. The unit will sound a beep with each press of the buttons holding the button speeds up the upward or downward value selection. It is not intended to supply power to a low-voltage electrical system other than in a starter-motor application. EverStart Maxx Jump Starter Manual PDF: PPS1CWE 1000 Amp Battery Jump The Alarm Icon. You will notice the battery indicator increasing with successful charging once your peak Jump-Starter gets fully charged. The unit is intended to be used only in the upright position. Keep cord from heat, oil, and sharp edges. Allow the unit to cool down for several minutes before attempting to use the USB Ports again. The LCD screen will continue to display the Battery Status Icon and Battery Voltage Indicator. The unit remains on until the clamps are disconnected from the battery. Disconnect the USB-powered device and press the USB Power Button again to turn off the USB Ports immediately. Everstart Maxx Jump Starter comes with different charging ports which are suitable to charge PC and laptop batteries, TV, mobile phone and more. No Load (turn OFF all vehicle's accessories): The battery must be fully charged before testing the alternator. IMPORTANT If you know the unit is discharged, but the battery icon displays four solid bars as if the unit is fully charged when connected to a charging power source, this may be due to the internal battery having high impedance. Connect negative () black clamp to chassis or a solid, non-moving, metal vehicle component or body part. More than 24 hours may be needed to restore performance on some batteries. Turning off the controls will not reduce this risk. Make sure the LED Area Light Power Button is in the on position. The slot that it plugs into is located on the back of the unit. The function requires a resting/cooling period between attempts. This units USB Ports do not support data communication. JumpSmart 10-in-1 Portable Car Jump Starter Powerful 29600 mWh Lithium . Check polarity of battery posts. When the unit is properly connected to an AC power source, the LCD screen will display the following The bars on the Battery Status Icon represent the charge level of the units internal battery. The Fault Icon will flash. The LCD screen will display the Battery Status Icon and the Voltage Icon for 10 seconds before the unit shuts down automatically. WARNING Battery fluid is a diluted sulphuric acid and may cause personal injury or damage to property. Press the battery recondition button. All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. Drink large quantities of water and induce vomiting. Recommended Minimum AWG Size for Extension Cords for Battery Chargers. A nozzle adaptor is supplied that screws onto the end of the Sure Fit nozzle at the free end of the compressor hose. The charger included with your EverStart Maxx jump starter is an automatic charger that is designed to shut off once the battery is fully charged. In any of these cases, the backlit LCD screen will continuously display the following. Connect the red clamp first, then the black clamp. Bursting articles can cause serious injury. A spark near the battery may cause an explosion. Check battery charger and components periodically for wear and tear. Check for damaged parts. When disconnecting the charger, disconnect the AC cord, remove clamp from the vehicle chassis, and then remove the clamp from the battery terminal. The jump starter icon will flash to indicate the clamps are properly connected. Remove contaminated clothing. Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to persons. If battery acid comes in contact with skin, rinse immediately with water, then wash thoroughly with soap and water. Some appliances may not charge or operate with this unit. Set up the unit, connect the battery clamps and connect to the battery following steps 1 through 5 under Procedure in the Jump Starter. All visitors should be kept at a distance from work area. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage. Once the desired pressure has been entered, release the button and the flashing digital display will show the new selected pressure, as follows The new selected value is now stored in the units memory until it is manually reset. Excessive engine cranking can damage the vehicles starter motor. Page 9 7. Store the compressor hose, Sure Fit nozzle and nozzle adapter in the storage groove. Make sure the unit does not need to be recharged. With features like a backlit LCD screen, USB charging ports, and a built-in AC charger, this versatile device is perfect for household use. The backlit LCD Screen will display the Battery Status Icon, the Battery Voltage Indicator and the Clamp Icons.The + and signs above the Clamp Icons, the Reverse Polarity Icons and the Alarm Icon will flash. Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead acid battery. How to Charge a Jump Starter Pack - Bell Engineering Monitor the pressure on the LCD screen. Check that the unit has a full charge. Never allow red and black clamps to touch each other or another common metal conductor this could cause damage to the unit and/or create a sparking/explosion hazard. Consult the dealer or an experienced radio/TV technician for help. However, there is no guarantee that interference will not occur in a particular installation. The built-in LED Area Light is controlled by the area light on/off button on the control panel. The following actions turn the unit on and activate the LCD screen. To reduce the risk of serious injury or property damage. Charge the unit with the AC charging adapter for a full 20 hours before using for the first time. Press the engine start button. Whenever the clamps are properly connected to a battery. The Jump Starter Icon flashes. Do not use this jump starter on a watercraft. Always have protective eyewear when using this product: contact with battery acid may cause blindness and/or severe burns. Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump started. Friction can cause dangerous static-electrical sparks. All power switches should be in the OFF position when the unit is charging or not in use. Dont abuse cord. This product is not intended for commercial use. All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. Review cautionary markings on these products and on the engine. Everstart Maxx Jump Starter 1200:Start Your Car With Easily Do not use the unit for charging dry-cell batteries that are commonly used with home appliances. To recharge this unit, use only the supplied AC charger. To reduce risk of a spark near the battery: To stop the charging process at any time, press and hold the charge/voltage button for three seconds to return the unit to Standby Mode. Get the AC charging plug from the back of your Peak Jump-Starter. Dont use appliances in damp or wet locations. The backlit LCD screen will display the Battery Status Icon, Battery Voltage Indicator, and the Clamp Icons. Contact the manufacturer at 1-877-571-2391 for more information. Then seek medical attention. CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or property damage. The battery charge gauge points to 100%, indicating a full charge. The Clamp Icons, + and signs and the Alarm Icon will flash. Do not connect clip to carburetor, fuel lines or sheet-metal body parts. The Fault Icon will flash. For this reason, it is of the utmost importance that each time before using the jump-starter you read this manual and follow instructions exactly. Never allow battery acid to come in contact with this unit. Place vehicle in park and set the emergency brake. Return to manufacturer for replacement of worn or defective parts immediately. If the unit detects that the alternator is good, the backlit LCD screen will display the following The Battery Status Icon, Alternator Icon, and ALT GOOD will light solid. Review cautionary markings on this product and on engine. To ensure safe and effective use of this product, it is important to carefully read and follow the instructions provided in the user manual. The unit remains in float charge mode as long as the charger is connected to the battery and plugged into a functioning AC outlet. Reorient or relocate the receiving antenna. Connect positive (+) red clamp to vehicle batterys positive terminal. If battery acid comes in contact with eyes, flush eyes immediately, for a minimum of 15 minutes and seek immediate medical attention. Improper connection can result in a risk of an electric shock. The bars on the Battery Status Icon will change from empty to solid bottom to top repeatedly to indicate the unit is charging. Before disposing of the battery, protect exposed terminals with heavy duty electrical tape to prevent shorting shorting can result in injury or fire. Proof of purchase may be required. Carefully connect the NEGATIVE (BLACK) charger clamp to the free end of the battery cable connected to the negative terminal. Make sure the Compressor Power Button has been pressed to turn the compressor on. In case of skin or eye contact, follow the instructions below. Therefore, if used in a garage or enclosed area, the unit MUST be placed not less than 18 inches above the floor. A marine (boat) battery must be removed and charged on shore. Red is positive; black is negative. 3. The unit remains on until the Alternator Check Button is pressed again to turn it off. The digital display shows the current voltage of the connected battery for 5 seconds. To jump-start your motorcycle, you'll need a portable jump starter, the motorcycle battery, and some jumper cables. Never immerse the battery charger in water or any other liquid, or use when wet. To stop the process sooner, press the battery recondition button a second time. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. THIS UNIT IS NOT FOR USE BY CHILDREN AND SHOULD ONLY BE OPERATED BY ADULTS. Immediately separate the clamps and do not allow them to touch again. EVERSTART MAXX JUMP PACK - YouTube